Teac US-100 Manual do Utilizador

US-100USB Audio InterfaceD01094020AOWNER'S MANUALThis device has a serial number located on the bottom panel. Please record it and retain it for

10 TASCAM US-100GuitarConnecting electronic instruments and CD/MD/cassette playersConnect the analog outputs of keyboards, drum machines and CD/MD/cas

TASCAM US-100 11Connecting monitor speakersConnectmonitorspeakers(poweredspeakersoranamplierand speakers) to the line output (OUTPUT) connect

12 TASCAM US-100This unit uses standard operating system drivers, so the necessary settings are the same for all audio applications, including Windows

TASCAM US-100 134 To adjust the input level, use the INPUT knob on the front panel of this unit. Adjust it so that the overload indicator (OL) does n

14 TASCAM US-100 Set the level of the “Device volume” to the highest position. Do not check the “Mute.” Then, click “OK” at the bottom of the window

TASCAM US-100 154 Click the “Recording” tab, click “Microphone: USB Audio CODEC,” and then click “Set Default.” The green checkmark is moved to “Micr

16 TASCAM US-100 Click the “Levels” tab. Set the level for “Speakers” to the maximum, then click “OK” at the bottom of both windows to close them. 7

TASCAM US-100 172 Click the “Audio Devices” tab. Set “Default Input,” “Properties for,” “Default Output” and “System Output” to “USB Audio CODEC.” F

18 TASCAM US-1005 Use the BALANCE knob to adjust the volume balance between the computer and input signals.Audio application settingsPlease consult t

TASCAM US-100 19If the unit does not function properly even though you have made setting according to the procedures in this Owner’s Manual, please re

2 TASCAM US-100 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus

20 TASCAM US-100B) Performance settings 1 Right-click “Computer,” select “System Properties,” and then click “Advanced system settings.” 2 Click the

TASCAM US-100 21Input and output ratingsMIC IN XLR connectorConnector: XLR-3-31 (1: GND, 2: HOT, 3: COLD)Inputimpedance:2.2kΩormoreNominal input

22 TASCAM US-100Total harmonic distortion (MIC IN to OUTPUT, when direct monitoring)0.1% or less(INPUT knob minimized: 1 kHz, –7 dBu input, Output lev

TASCAM US-100 23Dimensional drawingsIllustrations and other depictions may differ in part from the • actual product.Specifications and external appear

TEAC CORPORATIONPhone: +81-42-356-9143 www.tascam.jp1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan TEAC AMERICA, INC.Phone: +1-323-726-0303 www.tas

TASCAM US-100 3FOR U.S.A.TO THE USERThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

4 TASCAM US-100Table of Contents1 – Introduction ... 5Features ...

TASCAM US-100 5Thank you for purchasing the TASCAM US-100 USB Audio Interface. Please read this manual carefully before you begin using the unit so th

6 TASCAM US-100Additional information is introduced as needed in the • following categories. TIPThis is a useful hint about ways to use the unit.NOTEA

TASCAM US-100 72 – Part Names and FunctionsFront panelOverload indicatorSignal indicator USB indicatorHeadphones connector Output level adjustment kno

8 TASCAM US-100Rear panelUSB connector Line output connectorsLine input connectorsAnalog record player signal GND connector Input switchMicrophone inp

TASCAM US-100 9Connecting with a computerUse the included USB cable to connect the unit with a computer as shown in the illustration.USBComputerCAUTIO